| View previous topic :: View next topic |
| Author |
Message |
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
 Posted: Sat Oct 29, 2011 6:50 am Post subject: Screamingfast |
 |
|
Alrighty since I am starting to do some mods on my car might as well get "my garage" up.
Updated Mods List 3/20/2012
Current numbers 526rwhp/577rwtq
Engine:
P-51 Ported Eaton, TB, and Pletium
KB BAP
JLT Ram Air CAI
Diablo Mafia
2.76 upper pulley
LP I/C tank
170* thermostat
SCT custom Street tune
Drivetrain:
LMR built T-56 Tranny
Spec stage 5 clutch
26 spline input shaft
MGW Short Throw Shifter
Misc:
Autometer boost gauge
Autometer wide band/gauge
Suspension:
Factor Springs Cut
1.5 coils front
1.25 coils rear.
_________________
Last edited by ScreamingFast on Tue Mar 20, 2012 4:11 pm; edited 2 times in total |
|
| Back to top |
|
 |
Mystichrome
Laying Rubber
Joined: Mar 30, 2011
Posts: 1402
Location: Jacksonville
|
| Posted: Sat Oct 29, 2011 6:54 am Post subject: |
|
|
| I like your wheel idea a lot. That's very unique! I'm pumped to see your numbers after rh p-51 port! |
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
| Posted: Sat Oct 29, 2011 7:01 am Post subject: |
|
|
So am I!!! I am hope 490rwhp or better!! I got the rim idea from a red cobra with the same idea using a red pin stripe. If I find the pic I will post it.
_________________
|
|
| Back to top |
|
|
chrisman242
Noob
Joined: Apr 01, 2011
Posts: 81
|
| Posted: Wed Dec 21, 2011 8:54 pm Post subject: |
|
|
i think the yellow paint is good for at least 40 rwhp over all other colors.  |
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
| Posted: Sat Jan 07, 2012 4:45 am Post subject: |
|
|
P51 ported eaton is going on Sunday!! Going to take pics and video when all is done. Might be doing a heat exchanger swap with Jeff soon too.
_________________
|
|
| Back to top |
|
|
6Stang99
Smokin' Tires
Joined: Apr 23, 2009
Posts: 4541
Location: New Jersey...
|
| Posted: Sat Jan 07, 2012 7:48 am Post subject: |
|
|
Nice!
_________________
2010 PLATINUM MEMBER |
|
| Back to top |
|
|
BlackSheep
Parts Changer
Joined: Jul 27, 2011
Posts: 241
Location: JVegas, NC
|
| Posted: Sat Jan 07, 2012 10:53 am Post subject: |
|
|
I havent installed the springs jeff gave me yet but i noticed you said your factory springs are cut. obviously it lowers your ride height but how's the ride quality... not too rough like an aftermaket spring and still somewhat soft and absorbant??
_________________
99 Mustang GT SMR# 2070
"You So Bajitte" |
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
| Posted: Sat Jan 07, 2012 3:12 pm Post subject: |
|
|
Cobra Spring are a progressive spring so the will not be as harsh as cutting spring off a GT.
_________________
|
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
| Posted: Sun Jan 08, 2012 7:20 pm Post subject: |
|
|
So the new P-51 port eaton is on! Install was pretty easy for the most part but the wait to get this done was worth it!!! Car is much stronger now and if I had to guess we picked up 35-40 rwhp. I hope it shows at the track with a good trap speed. I think I am going to bite the bullet and get a lower pulley down the road along with larger injectors (60s) and hope it push over 500rwhp. I have a video that is up loading to youtube and will post it soon here. We did a couple of video pulls but the one post was just of us data logging the car before tunning it. Wish we would have gotten some after tunning pulls. To come soon thou.
_________________
|
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
|
| Back to top |
|
|
Mystichrome
Laying Rubber
Joined: Mar 30, 2011
Posts: 1402
Location: Jacksonville
|
| Posted: Sun Jan 08, 2012 7:33 pm Post subject: |
|
|
| Glad to see its all done! |
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
| Posted: Sun Jan 08, 2012 7:36 pm Post subject: |
|
|
No sir thank you for your help Brandon. I think you might have someone interesed in buying your new/used eaton!
_________________
Last edited by ScreamingFast on Mon Jan 09, 2012 4:00 am; edited 1 time in total |
|
| Back to top |
|
|
DarknessGT
Dangerous
Joined: May 02, 2011
Posts: 662
Location: J-Ville, NC
|
| Posted: Sun Jan 08, 2012 7:41 pm Post subject: |
|
|
| That is freaking sick! What are you hoping to run at the track? |
|
| Back to top |
|
|
ScreamingFast
Site Admin
Joined: Aug 17, 2008
Posts: 11381
|
| Posted: Sun Jan 08, 2012 7:46 pm Post subject: |
|
|
Well I am a average driver so if I can run 11.8's or 11.7's I would be happy with that. The car could do that before the port with a driver mod so with new port and good driver I say the car can pull 11.4's
_________________
|
|
| Back to top |
|
|
Mystichrome
Laying Rubber
Joined: Mar 30, 2011
Posts: 1402
Location: Jacksonville
|
| Posted: Sun Jan 08, 2012 7:51 pm Post subject: |
|
|
| ScreamingFast wrote: | | No sir thank you for your help Brandon. I think you might have some interesed in buying your new/used eaton! |
Sounds good to me. Just let me know! |
|
| Back to top |
|
|
|
Forum FAQ
Search
Usergroups
Profile
Log in to check your private messages
Log in
